Back
Previous product
Livewell Pump Angled Thru-hull Inlet, Dual Port, 500-800-1100 GPH (RWB5231V) (a) RULE Livewell Pump Angled Thru-hull Inlet, Dual Port, 500-800-1100 GPH Price range: $135.00 through $185.00 inc GST
Next product
Livewell Pump Straight Thru-hull, Dual Port, 500-800-1100 GPH (RWB5230V) (a) RULE Livewell Pump Straight Thru-hull, Dual Port, 500-800-1100 GPH Price range: $135.00 through $186.00 inc GST
-21%
Livewell Pump Straight Seacock Inlet, Dual Port, 500-800-1100 GPH (RWB5232V) (e)
Livewell Pump Dual Port, 500-800-1100 GPH (b)
Livewell Pump Straight Seacock Inlet, Dual Port, 500-800-1100 GPH (RWB5232V) (b)
Livewell Pump Straight Seacock Inlet, Dual Port, 500-800-1100 GPH (RWB5232V) (d)
Livewell Pump Straight Seacock Inlet, Dual Port, 500-800-1100 GPH (RWB5232V) (c)
Livewell Pump Dual Port, 500-800-1100 GPH (a)
Livewell Pump Dual Port, 500-800-1100 GPH (g)
Livewell Pump Dual Port, 500-800-1100 GPH (f)
Livewell Pump Dual Port, 500-800-1100 GPH (e)
Livewell Pump Dual Port, 500-800-1100 GPH (d)
Livewell Pump Dual Port, 500-800-1100 GPH (c)

RULE Livewell Pump Straight Seacock Inlet, Dual Port, 500-800-1100 GPH

Price range: $135.00 through $180.00 inc GST

SKU: RWB5232V

Livewell Pump Straight Seacock Inlet, Dual Port, 500-800-1100 GPH

     
   

Model SKU Price Cart Stock
500 GPH
RWB5232
Original price was: $170.00.Current price is: $135.00. inc GST

On Backorder

800 GPH
RWB5235
Original price was: $196.00.Current price is: $155.00. inc GST

On Backorder

1100 GPH
RWB5238
Original price was: $223.00.Current price is: $180.00. inc GST

On Backorder

SKU: RWB5232V Categories: ,

UPC: 

Condition:  New

Out of Stock

Description

Description

RULE Livewell Pump Straight Seacock Inlet, Dual Port, 500-800-1100 GPH

  • NOTE: The old Rule 400 series are replaced by these new pump series.
  • These pumps comes with a simple and convenient “push and twist button” motor cartridge removal system makes it easy to remove and replace the motor cartridge when fitted in hard-to-reach areas of the boat.
  • These are rated to take up to 600 PSI of pressure from high-speed pickup scoops.
  • Also available in angled thru-hull or seacock installation (Sold seperately. Refer to list below.)
  • Eco-friendly cardboard hang or stack box packaging and plastic blister packs.

About Xylem’s Rule Livewell Pumps

  • Provide ultimate pumping performance, which helps keep the bilge clear of nuisance water.
  • Offers three (3) types of bilge pumping solutions:
    • Electric driven pumps that are either installed in lowest part of the bilge or dry installed with a suction line.
    • Engine driven pumps that are installed on and driven by the boat motor.
    • Manual solutions with hand operated pumps.

Good Fishing Begins with Good Bait

  • For over 50 years, boat builders and owners have depended on Rule pumps for a fun day out on the water. Building on that legacy of marine
    performance, Xylem’s Rule Livewell Pumps have been designed to deliver superior performance and unsurpassed quality – making it the
    perfect choice for keeping bait and catch alive.

  • To meet the needs of today’s faster watercraft, this livewell pump can withstand the pressures of high-speed water intake scoops.
  • Other features that provide enhanced operation and reliability:
    • High efficiency pump design for optimal bait health.
    • Simple one hand twist & click motor cartridge removal or replacement.
    • Inlets for straight thru-hull, angled thru-hull and seacock installations.
    • Secondary inlet port for washdown pump connection.
    • Advanced anti-airlock protection.

High-Efficiency Motor and Impeller Design

  • The advanced engineering of the Rule Livewell Pumps ensures more efficient water circulation, which is crucial for maintaining the well-being of bait/catch in the livewell.

Adaptable to Different Setups and Configurations

  • All Rule Livewell Pumps are supplied with threaded nylon hose barb attachments, making them adaptable to different setups and configurations and allowing for versatile hose mounting options.

High Inlet Pressure Capability for High-Speed Vessels

  • While other livewell pumps are not engineered to withstand the additional water pressures of boats with high-speed pickup scoops, the Rule Livewell Pumps feature a high inlet pressure capability that can keep up with the demands of more powerful boats.

See the complete specifications in the table below (Refer to image gallery for sizing guide)

PRODUCT PART NUMBER

OLD/PREVIOUS PRODUCT PART NUMBER

XYLEM MODEL NUMBER

*GPH @ OPEN FLOW (**LPH)

GPH @ 3.3 ft. (LPH @ 1m)

INLET STYLE / TYPE

PORT TYPE

INLET SIZE (***NPT/****NPSM)

DISCHARGE SIZE – HOSE BARB

VOLTAGE

Amp @ 12V DC

FUSE SIZE (Amps)

REPLACE MOTOR CARTRIDGE

SIZE A

SIZE B

SIZE C (THREAD)

SIZE D (THREAD)

SIZE E (THREAD)
RWB5232

RWB0056

601FC

500 GPH (1892 LPH)

425 GPH (1609 LPH)

Straight Seacock

Dual

3/4″ NPT Thread

3/4″

12V DC

3.0A

5A

65 DR

—

5.62″ (142.8mm)

1-11.5 NPSM

1/2-14 NPT

3/4-14 NPT
RWB5235

RWB0057

603FC

800 GPH (3028 LPH)

600 GPH (2271 LPH)

Straight Seacock

Dual

3/4″ NPT Thread

3/4″

12V DC

4.1A

7.5A

66 DR

—

5.62″ (142.8mm)

1-11.5 NPSM

1/2-14 NPT

3/4-14 NPT
RWB5238

RWB0058

605FC

1100 GPH (4163 LPH)

825 GPH (3123 LPH)

Straight Seacock

Dual

3/4″ NPT Thread

1 1/8″

12V DC

4.7A

7.5A

67 DR

—

5.62″ (142.8mm)

1-11.5 NPSM

1/2-14 NPT

3/4-14 NPT

*Gallons per hour; **Liters per hour; ***National Pipe Thread; ****National Pipe Straight Mechanical.

Also available in Angled version. Refer to the following. (Sold seperately)

  • RWB5231 500GPH, Dual Port, Angled Thru-hull
  • RWB5234 800GPH, Dual Port, Angled Thru-hull
  • RWB5237 1100GPH, Dual Port, Angled Thru-hull

Also available in Straight Thru-hull version. Refer to the following. (Sold seperately)

  • RWB5230 500GPH, Dual Port, 3/4″ thread, Straight Thru-hull
  • RWB5233 800GPH, Dual Port, 3/4″ thread, Straight Thru-hull
  • RWB5236 1100GPH, Dual Port, 3/4″ thread, Straight Thru-hull

For spare or replacement motor cartridge (suits Livewell Pumps), refer to the following. (Sold seperately)

  • SP0910 500GPH
  • SP0911 800GPH
  • SP0912 1100GPH

Refer to Xylem website for further details on user guide.


TO CHANGE MOTOR CARTRIDGE (Refer to image gallery for visual guide)

  • 1. Block off the thru-hull before removing the motor cartridge.
  • 2. Disconnect wiring.
  • 3. Press cartridge release button, twist counterclockwise and pull motor cartridge straight up.
  • 4. Reconnect wire to new motor cartridge.
  • 5. Install the new motor cartridge and press down firmly. Twist motor housing clockwise until cartridge locks in place. A “click” should be heard when the cartridge is locked.
  • 6. Open or unblock thru-hull to begin use.

WARNING: The operator of the vessel should ensure the motor cartridge is in the fully locked position at all times when the vessel is in the water. Failure to place the motor cartridge in the fully locked position could result in water intrusion, flooding, property damage, severe personal injury and/or death.

WARNING: This pump is designed for water only. Use with any other medium, including flammable, hazardous, caustic or corrosive fluid, may result in damage to the pump, the surrounding environment, property damage, severe personal injury and/or death.

All pumps are tested at nominal voltage with fresh water at ambient temperature with no ports attached. (Open flow).


MOUNTING THE PUMP (Refer to image gallery for visual guide)

For Models 601C, 601STC, 603C, 603STC, 605C, 605STC

  • 1. Pumps need to be mounted below the waterline as they are not self-priming pumps.
  • 2. With vessel out of the water, drill a 1” (25mm) diameter hole through the transom or hull bottom. If drilling through the transom, make sure the hole inside the boat is beneath the waterline outside the boat when the boat is standing still.
  • 3. Place the pump into the hole with the gasket in place on the inside of the boat.
  • 4. Use below water, marine grade sealant on both sides of the hole when installing pump and before the nut is tightened.
  • 5. Tighten the nut on the outside of the hull until you are sure the gasket ring is tightly sealed. Be careful not to overtighten.
  • 6. Make sure outlet is at least parallel with boat bottom. This helps prevent airlocks.
  • 7. Saw off the excess length of the pickup tube so it is flush with the outside surface of the nut. In the event you are using a strainer (Rule Model 73), leave 1/2” (13mm) beyond the nut. Make sure the cut is square and the threads deburred to allow the debris strainer to fit smoothly.

SEACOCK APPLICATIONS (Refer to image gallery for visual guide)

For Models 601FC, 603FC, 605FC

  • 1. Pumps need to be mounted below the waterline as they are not self-priming pumps.
  • 2. With vessel out of the water, drill a 1” (25mm) diameter hole through the transom or hull bottom. If drilling through the transom, make sure the hole inside the boat is beneath the waterline outside the boat when the boat is standing still.
  • 3. Install a thru-hull pickup tube with a filter grate to prevent debris from entering the seacock and the pump. Use a marine sealant on the flat surface of the thru-hull where it will be in contact with the outside surface of the boat and around the threaded tube on both sides of the hull. Install the seacock and pump using pipe tape or sealant on all threaded connections.
  • 4. Screw the pump into the seacock until it is hand tight. Do not over-tighten.
  • 5. If the pump is mounted horizontally, the output must be pointed upward to allow air to vent.
  • 6. Plumbing should run in a constant upward direction with no dips to prevent air locks in the pump.

WARNING: Failure to keep the seacock closed when the livewell is not in use could lead to water intrusion, flooding, property damage, severe personal injury and/or death.


ELECTRICAL APPLICATIONS

    WIRE: Normal installations require 16 gauge wire.

    POLARITY: Brown pump wire connects to the positive (+) side of the battery. Black pump wire connects to the negative (—) side of the battery.

    FUSE: Install proper size fuse & holder in the positive (+) brown wire between the pump and the battery.

    • 500 GPH pumps (Models 601C, 601FC, 601STC) – INSTALL A 5.0 AMP FUSE.
    • 800 GPH pumps (Models 603C, 603FC, 603STC) – INSTALL A 7.5 AMP FUSE.
    • 1100 GPH pumps (Models 605C, 605FC, 605STC) – INSTALL A 7.5 AMP FUSE.

CAUTION: Always install proper fuse size to prevent damage to product should a short occur. Failure to install proper fuse could increase risk of pump malfunction, potentially resulting in personal injury and/or fire hazard.

NOTE: Keep all wire connections and joints above highest possible water level. Seal wire connections
with a marine sealant to prevent corrosion.


HOSE CONNECTION – DUAL PORT OPTION

Each pump is fitted with an additional 1/2” NPT female port and Hex Plug. This feature allows you to add your washdown pump without adding another thru-hull fitting.

  • Use a marine ribbed hose that will not kink with bends and is rated for below water line use.
  • Hose should run uphill evenly from pump to livewell tank.
  • You may use a control valve to regulate the flow.
  • Use hose clamps when making connections to pump and valve

MAINTENANCE (EVERY 6 MONTHS)

  • Close seacock or remove vessel from the water.
  • Remove motor cartridge.
  • Inspect impeller and replace motor cartridge if impeller is damaged.
  • Inspect impeller for debris and remove all foreign matter.
  • Install motor cartridge to the fully locked position.
  • Open seacock or place vessel in water.
  • Check system for leaks and correct operation.

CAUTION: The pump is below the waterline. Water can come into the boat through the pump if the hose is not connected tightly to the pump.

AIS (Aquatic Invasive Species) Decontamination Process. All of the pumps are designed to meet the ABYC standards for the current
AIS Decontamination Procedure including low pressure water at 120ºF for 130 seconds. Please follow current guidelines for the decontamination process.


WARNING: Do not modify or alter the pump in any way as this could lead to water intrusion, flooding, property damage, severe injury and/or death.

NOTICE: END OF LIFE DISPOSAL Handle and dispose of all waste in compliance with local laws and regulations.

Additional information

Additional information

Brand

Rule

Condition

New

Shipping

Price does not include shipping. Product will be shipped via Toll / Australia Post / Courier. Product can also be collected.

Model

1100 GPH, 500 GPH, 800 GPH

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “RULE Livewell Pump Straight Seacock Inlet, Dual Port, 500-800-1100 GPH”

Your email address will not be published. Required fields are marked *

Shipping & Delivery
Prices do not include shipping.

Shipping quotes can be obtained by adding products to the cart and inputting your postcode.

$11.60 Brisbane Express - Postcodes 4000-4209, 4270-4299, 4500-4549, 9000-9725 up to 20kg

Boat Hut uses Toll Ipec Priority Service, Australia Post Express Post and Courier's Please. Boat Hut uses Australia Post or DHL International Service for New Zealand deliveries.

Free Local Pickup – by prior arrangement. We don’t always have all the products at our Acacia Ridge premises, but they may be at our warehouse. Warehouse collections can be arranged by prior arrangement - please contact us to discuss.

Order Tracking provided on all orders.

All orders will be processed within 2 business days - except backordered items. If we are unable to meet this timeframe we will contact you to provide details and options. If we are unable to ship your order within 3 business days we will offer you a refund in full or the option to wait for the goods to come into stock.

We are happy to ship to any country - and will provide a quote upon request. All overseas orders must be paid for via Paypal before your order is shipped.

Above pricing refers to regular size items that will fit in courier satchels - oversized items will require a freight quote.

Boat Hut reserves the right to refuse to fulfil an order that has the incorrect postage / freight collected at the time of sale. We will work with you to rectify the matter, if we are unable to come to a resolution then we will provide a refund in full.


Stock Availability

**We accept advanced orders on backordered items.**

**For stock confirmation and other inquiries, kindly reach us through phone at 1300-773332 (1300 SPEEDBOAT) or 07-3039-3100 or Text Us in the bottom right of the screen and we will be in contact with you.**

**ABOUT BOAT HUT**

Boat Hut has approximately 100,000 product lines coming from a number of warehouses across Australia. All products of Boat Hut are genuine and comes with manufacturer’s warranties.

Not all of these products are available for a walk-in purchase at Acacia Ridge - most times you will need to make arrangments in advance.
Please feel free to contact us to confirm our stock at Acacia Ridge or in our warehouses.
We try our best to keep the website up to date with current stock holdings.

Recently Viewed Products

Lewmar Blocks – Control Single 30mm

Original price was: $41.90.Current price is: $37.06. inc GST

In stock