Description
Hansen 32mm (1 1/4”) Ball Valve Handle in LILAC / HBVHL32
This is an accessory handle for full flow ball valve range.
Lilac handle is suitable for grey water applications.
SPECIFICATIONS
- PRODUCT CODE: HBVHL32
- PRESSURE AND FLOW RATES
- FITTING SIZE: 15-50mm
- MAXIMUM PRESSURE @ 20º DEGREE CELCIUS/68º FAHRENHEIT: 16 Bar (1600 kPa, 235 PSI)
Hansen have tested all its products for use with cold water up to a maximum temperature of 60ºC (140ºF). It is not recommended the use of these products higher than 60ºC (140ºF) as plastic expands due to temperature increases. Hansen cannot guarantee the products will perform when used with temperatures over 60ºC (140ºF). Hansen products that have failed in temperatures higher than 60ºC (140ºF) will not be covered by limited lifetime warranty. - CHEMICAL RESISTANCE
- Please refer to the attached images for full chart of chemical resistance.
- DIMENSIONS (See attached image or below chart for sizing guide)
- METRIC: 32mm
- IMPERIAL: 1 1/4”
- This is compatible with HBVL25 25mm Ball Valve, Lilac and HBV25MF 25mm Male/Female Ball Valve.
- HANDLE COLOUR: LILAC
FEMALE BALL VALVE DIMENSIONS
| PRODUCT CODE | T1 BSPT/NPT (DN – NORMAL BORE SIZE) | T2 BSPT/NPT (DN – NORMAL BORE SIZE) | SIZE A | SIZE B | SIZE C | SIZE D | SIZE E |
| HBV15 | 15mm (1/2″) | 15mm (1/2″) | 98mm | 82mm | 93mm | 56mm | 54mm |
| HBV20 | 20mm (3/4″) | 20mm (3/4″) | 98mm | 82mm | 93mm | 56mm | 54mm |
| HBV25 | 25mm (1″) | 25mm (1″) | 111mm | 93mm | 104mm | 65mm | 61mm |
| HBV32 | 32mm (1 1/4″) | 32mm (1 1/4″) | 122mm | 107mm | 112mm | 76mm | 69mm |
| HBV40 | 40mm (1 1/2″) | 40mm (1 1/2″) | 135mm | 124mm | 123mm | 90mm | 79mm |
| HBV50 | 50mm (2″) | 50mm (2″) | 146mm | 140mm | 131mm | 106mm | 89mm |
MALE/FEMALE BALL VALVE DIMENSIONS
| PRODUCT CODE | T1 BSPT/NPT (DN – NORMAL BORE SIZE) | T2 BSPT/NPT (DN – NORMAL BORE SIZE) | SIZE A | SIZE B | SIZE C | SIZE D | SIZE E |
| HBV25MF | 25mm (1″) | 25mm (1″) | 131mm | 93mm | 104mm | 65mm | 61mm |
| HBV32MF | 32mm (1 1/4″) | 32mm (1 1/4″) | 142mm | 107mm | 112mm | 76mm | 69mm |
| HBV40MF | 40mm (1 1/2″) | 40mm (1 1/2″) | 155mm | 124mm | 123mm | 90mm | 79mm |
| HBV50MF | 50mm (2″) | 50mm (2″) | 170mm | 140mm | 131m | 106mm | 89mm |
- BODY AND END CAPS MATERIAL: Glass Fibre Reinforced Nylon
- HANDLE MATERIAL: Glass Fibre Reinforced Nylon
- BALL MATERIAL: Polypropylene
- BALL SEATS AND STEM: Acetal (POM)
- O-RINGS MATERIAL: EPDM
- HANSEN Full Flow Ball Valves are WRAS Approved Product, see certificate here.
- HANSEN Full Flow Ball Valves are IMCI Approved Product, see certificate here.
- HANSEN Full Flow Ball Valves are AS/NZS 4020:2018 Approved, see certificate here.
OTHER AVAILABLE BALL VALVES WITH LILAC HANDLE (Available as seperate purchase)
- HBVHL15/20, 15/20mm (1/2”- 3/4”)
- HBVHL25, 25mm (1”)
- HBVHL40, 40mm (1 1/2”)
- HBVHL50, 50mm (2”)
FEATURES
- Versatile full flow ball valve, lightweight and strong.
- All Hansen Full Flow Ball Valves are rigorously hand tested.
- With smooth action of ‘OPEN’ and ‘CLOSE’ that helps reduce surge which can cause damage to your system. Positive ‘CLICK’ gives the assurance the valve is either on or off. Removable handles for security and varying applications.
- Male/Female or Female Thread Option, available in various thread options to suit a range of applications.
- With maximum working pressure or high pressure rating of 16 Bar/235 psi at 20°C.
- Full flow bore, the unrestricted full flow blow valve gets the job done faster. With less system strain and lower maintenance costs.
- With high quality materials, uses body and end caps (made of glass fibre reinforced nylon), handle (glass fibre reinforced nylon), ball (polypropylene), Ball seats and stem (Acetal (POM), O-rings (EPDM).
- Corrosion Proof and Potable Water Approved, manufactured from non-corrosive, UV stabilised materials, potable water and marine approved and salt-water friendly.
- The Hansen Ball Valves are frost friendly and have been tested in frost conditions. Results may vary in freezing conditions.
- With different handles for varying applications. International colour coded handles, available as seperate accessories: BLUE (for general applications), LILAC (for grey water applications), GREEN (for increased visibility and to differentiate)
- Will function across a wide range of operating pressure and temperatures.
FULL FLOW BALL VALVES – INSTALLATION STEPS (See image gallery for visual guide)
- All pipe work must be adequately supported.
- Use a thread sealant on all threaded connections. It is recommended to use Loctite 5331.
- If you are using chemicals or have any special requirements that you wish to use your Ball Valves for, kindly see the Chemical Resistance chart.
- Fittings should be installed as per applicable standards and approvals for pipe and fittings. Failure to complete installation in accordance with applicable standards and approvals may void warranties given by Hansen Products (NZ) Limited in respect to the fitting. It is recommended to follow piper manufacturer’s guideline.
- 1.) Use a teflon tape sealant or a thread paste sealant. The right sealant for threaded joints is non-hardening, compatible with plastic and doesn’t add slipperiness to encourage over-torquing.
- 2.) Screw pipe or fitting into Ball Valve.
- 3.) Do not over tighten. The recommended way to assemble a Ball Valve is finger tight. Tighten until firm with spanner or pipe grip. One or two turns should be all that is required.
FULL FLOW BALL VALVE HANDLE REMOVAL STEPS (See image gallery for visual guide)
- 1.) Turn handle clockwise slightly.
- 2.) Put fingers under handle and pull whilst pushing with thums on body of valve.
VALVE OPEN OR CLOSED (For visual guide, kindly see image gallery).
- OPEN Valve is identified as OPEN when the centre notch is not parallel with the valve body.
- CLOSED Valve is identified ad CLOSED when the centre nothc is paraller with the valve body.
FITTINGS BROCHURE AND CHEAT SHEETS
FREQUENTLY ASKED QUESTIONS
- Q: Are Hansen Ball Valves frost friendly?
- A: Hansen Ball Valves are frost friendly and have been tested in frost conditions. Results may vary in freezing conditions.
- Q: Can I use my Hansen Ball Valve with my swimming pool/spa pool set up?
- A: No, as the high concentration of chlorine used in the water for pools, will attack the material. The fitting material is only suitable for use with domestic water. Hansen products that are used in this application will not be covered by our Hansen Warranty.
- Q: Can I use these Ball Valves with metal fittings?
- A: Yes.
- Q: Do I need to support my Ball Valve?
- A: Yes. All pipe work must be adequately supported.
- Q: How tight should I tighten my Ball Valves?
- A: Do not over tighten. The right way to tighten a Ball Valve is hand tight plus one to two turns-no more.
- Q: What temperature can I use Hansen Ball Valves at?
- A: Hansen have tested all its products for use with cold water up to a maximum temperature of 60°C (140°F). It is not recommended to use these products with temperatures higher than 60°C (140°F) as plastic expands due to temperature increases. Hansen cannot guarantee the products will perform when used with temperatures over 60°C (140°F). Hansen products that have failed in temperatures higher than 60°C (140°F) will not be covered by our Hansen Warranty.
- Q: What type of sealant should I use?
- A: Use a thread sealant on all threaded connections. It is recommended to use Loctite 5331.
