Description
Hansen 65mm (2 1/2”) Hex Screw Cap / HCP65
This is a 65mm (2 1/2”) Hex Screw Cap that is used for capping off Male Threads. BSPT.
SPECIFICATIONS
- PRODUCT CODE: HCP65
- CODE MEANING: HANSEN HEX SCREW CAP
- PRESSURE AND FLOW RATES
- Please refer to the attached images for full chart of chemical resistance.
- DIMENSIONS
- PRODUCT CODE: HCP65
- T1 BSPT: 65mm (2 1/2”)
- SIZE A (Across Flats): 90.5mm
- SIZE B: 43.5mm
PRODUCT CODE T1 BSPT Size A (Across Flats) Size B HCP15 1/2″ (15mm) 28.5mm 22mm HCP20 3/4″ (20mm) 34.5mm 23mm HCP25 1″ (25mm) 41.5mm 27mm HCP32 1 1/4″ (32mm) 52mm 31.5mm HCP40 1 1/2″ (40mm) 58.5mm 37mm HCP50 2″ (50mm) 71.5mm 38mm HCP65 2 1/2″ (65mm) 90.5mm 43.5mm HCP80 3″ (80mm) 106.5mm 47.5mm HCP100 4″ (100mm) 133.5mm 57mm
- TRUE FIT PIPE FITTINGS MAXIMUM WORKING PRESSURES (See image gallery for visual chart and guide)
| FITTING SIZE | MAX PRESSURE @ 20º DEGREE CELCIUS/68º FAHRENHEIT |
| 6mm-50mm | 16 Bar (1600 kPa, 235 PSI) |
| 65mm | 12 Bar (1200 kPa, 175 PSI) |
| 80mm-100mm | 10 Bar (1000 kPa, 145 PSI) |
Hansen have tested all its products for use with cold water up to a maximum temperature of 60ºC (140ºF). It is not recommended the use of these products higher than 60ºC (140ºF) as plastic expands due to temperature increases. Hansen cannot guarantee the products will perform when used with temperatures over 60ºC (140ºF). Hansen products that have failed in temperatures higher than 60ºC (140ºF) will not be covered by limited lifetime warranty.
CHEMICAL RESISTANCE OF TRUE FIT THREADED FITTINGS
FEATURES AND BENEFITS
- Largest range of durable, high strength, commercial quality threaded pipe fittings in the Southern Hemisphere.
- Precision, heavy duty, tapered threads give a strong reliable seal.
- Manufactured from a raw material approved for use with potable (drinkable) water.
- Manufactured from high quality glass fibre, reinforced nylon, giving a weather, termite, fungi and bacteria resistant.
- Common applications include horticultural, agricultural, irrigation, marine & plumbing.
- Material strong enough to minimise potential cross threading.
- Suitable for use above or below ground in varying operating pressures and temperatures.
- Strong, lightweight and compact.
- Available in a variety of thread combinations and connections.
- New Zealand Made.
OTHER AVAILABLE SIZE OF HEX SCREW CAP IN HCP
- HCP15 15mm (1/2”)
- HCP20 20mm (3/4”)
- HCP25 25mm (1”)
- HCP32 32mm (1 1/4”)
- HCP40 40mm (1 1/2”)
- HCP50 50mm (2″)
- HCP80 80mm (3”)
- HCP100 100mm (4”)
FITTINGS BROCHURE AND CHEAT SHEETS
- For HANSEN True Fit Threaded Fittings Brochure and Cheat Sheets, refer to Hansen Australia Website.
HANDY TIPS AND COMMERCIAL VIDEOS
- For HANSEN True Fit Threaded Fittings Handy Tips and TV Commercial videos, refer to Hansen Australia Website.
TRUE FIT THREADED FITTINGS QUICK AND EASY INSTALLATION STEPS (See full installation in image gallery or attached image)
- 1.) (a) Use a thread paste sealant or (b) a teflon tape sealant. The right sealant for threaded joints is non-hardening, compatible with plastic and doesn’t add slipperiness to encourage over-torquing.
2.) Screw pipe into fitting. Do not over tighten. The recommended way to assemble a Threaded Pipe Fitting is hand tight. Tighten until firm with spanner or pipe grip. One to two turns should be all that is required.
- All pipe work must be adequately supported.
- Use a thread sealant on all threaded connections. It is recommended to use Loctite 5331.
- If you are using chemicals or have any special requirements that you wish to use your Threaded Pipe Fitting in, see the Threaded Chemical Resistance chart in the image gallery.
- Please see below for Minimum Recommended Hole Sizes chart.
- Fittings should be installed as per applicable standards and approvals for pipe and fittings. Failure to complete installation in accordance with applicable standards and approvals may void warranties given by Hansen Products (NZ) Limited in respect to the fitting. It is recommended to follow pipe manufacturers guidelines.
FREQUENTLY ASKED QUESTIONS
- QUESTION: Can I use Hansen True Fit Fittings under driveways, paths and foundations?
- ANSWER: Hansen does not recommend the use of any Hansen True Fit Fittings under any driveways, paths or foundations.
- QUESTION: Can I use my Hansen fittings with my swimming pool/spa pool set up?
- ANSWER: No, as the high concentration of chlorine used in the water for pools will attack the material. The fitting material is only suitable for use with domestic water. Hansen products that are used in this application will not be covered by our Hansen Warranty..
- QUESTION: Can I use these fittings with metal fittings?
- ANSWER: Yes. For more information on installation tips refer to installation instructions.
- QUESTION: Do I need to support my fittings?
- ANSWER: Yes. All pipe work must be adequately supported.
- QUESTION: Does this fitting carry the Hansen Warranty?
- ANSWER: Yes, all Hansen manufactured products carries a Hansen Warranty.
- QUESTION: How tight should I tighten my Hansen threaded fittings?
- ANSWER: Do not over tighten. The right way to assemble a threaded fitting is hand tight plus one to two turns – no more! For more information on installation tips refer to installation instructions.
- QUESTION: What temperature can I use Hansen fittings at?
- ANSWER: Hansen have tested all its products for use with cold water up to a maximum temperature of 60°C (140°F). It is not recommended to use of these products with temperatures higher than 60°C (140°F) as plastic expands due to temperature increases. Hansen cannot guarantee the products will perform when used with temperatures over 60°C (140°F). Hansen products that have failed in temperatures higher than 60°C (140°F) will not be covered by the Hansen Warranty.
- QUESTION: What type of thread sealant should I use?
- ANSWER: Use a thread sealant on all threaded connections. It is recommended to use Loctite 5331.
