Description
Hansen 25mm (1″) Female BSPT Superflo Piston Valve Body / HSFBODY
This is a spare or replacement part for Hansen Superflo Valves use.
SPECIFICATIONS
- PRODUCT CODE: HSFBODY
- CODE MEANING: HANSEN SUPERFLO BODY
- LENGTH: 25mm (1″)
- MAXIMUM WORKING PRESSURE: 12 Bar (174 psi) at 20 degrees ºC
- Hansen Superflo Valve will operate from .2 to 12 Bar (2.9 to 174 psi) at 20 degrees ºC
- SUPERFLO CHEMICAL RESISTANCE CHART: refer to image gallery for preview of chemical resistance chart.
- SUPERFLO PLASTIC VALVE FLOW CHART: refer to image gallery for preview of flow chart.
- Hansen Superflo Valve are 4020:2018 certified. Kindly refer to Hansen Australia Website for certificates and watermark approval previews.
- SUPERFLO DIMENSIONS (See visual dimension guide in image gallery)
LONG BRASS ARM
T1 AND T2 BSPT (DN) SIZE (a) PLASTIC VALVE SIZE (a) BRASS VALVE SIZE (b) SIZE (c) 1″ (25mm) 376mm 371mm 83mm 58mm
SHORT BRASS ARM
| T1 AND T2 BSPT (DN) | SIZE (a) PLASTIC VALVE | SIZE (a) BRASS VALVE | SIZE (b) | SIZE (c) |
| 1″ (25mm) | 250mm | 245mm | 83mm | 58mm |
- TROUGH INSTALLATION
- Flush pipe lines into water troughs before installing Super˙
Flo Valve into new system. - Isolate the water trough to replace valve in existing scheme.
- Put thread tape on adaptor side that does not have O-ring and start the adaptor
into trough inlet.
- SUPERFLO SIDE/TOP ENTRY
- SUPERFLO SIDE ENTRY (See visual guide in image gallery)
- Thread Superflo Valve onto adaptor & tighten.
- Screw the nut with cord onto the Superflo Brass arm.
- Thread cord through the Superflo float. Tie the cord off to achieve the correct on/off and water level.
Cord and nuts only supplied with long arm
- SUPERFLO TOP ENTRY (See visual guide in image gallery)
- Thread Superflo Valve onto adaptor & tighten.
- Screw the float onto the brass arm.
- Hold the body of the valve at arm entry point.
- Bend brass arm to achieve the correct on/off and water level.
WALL THICKNESS GUIDE
| LONG TAIL ADAPTOR | HMAL15 | HMAL20 | HMAL25 | HMAL32 | HMAL40 | HMAL50 |
| TANK WALL | 14mm | 22mm | 19mm | 24mm | 45mm | 39mm |
Hansen Long Tail Adaptors Maximum Wall Thickness for Tanks when screwed into a Hansen Female Bend.
SUPERFLO PARTS AND MATERIALS
The Superflo Trough Valve is manufactured from Potable Water approved materials.
- Superflo Piston Valve Body Plastic or Brass
- Split Pin Stainless Steel
- Slipper Fit Piston Plastic
- Piston O-Ring Potable Water Approved
- Valve Body Washer Seal Thermoplastic Polyurethance Elastomer
- Valve Body Cap Nut Glass Fibre Reinforced Nylon
- Cord Polyester
ADAPTORS
- Adaptor Glass Fibre Reinforced Nylon
- Adaptor O-Ring EPDM (Ethylene Propylene)
FLOAT
- Float High Density Polyethylene
- Thread Insert Glass Fibre Reinforced Nylon
THIS IS SUITABLE WITH THE FOLLOWING VALVES (Available as seperate purchase)
- HSFPV2520 Superflo 25/20
- HSFPV2520L Superflo 25/20 Long
- HSFPV2015L Superflo 20/15 Long
- HSFPV2520S Superflo 25/20 Short Arm
- HSFPV2520B Superflo Brass 25/20
- HSFPV2520BL Superflo Brass 25/20 Long
- HSFPV2015BL Superflo Brass 20/15 Long
- HSFPV2520S Superflo 25/20 Short Arm
- HSFPV2015LS Superflo 20/15 Long/Short Arm
- HSFPV2520LS Superflo 25/20 Long/Short Arm
- HSFPV2520BLS Superflo Brass 25/20 Long/Short Arm
- HSFPV2015BLS Superflo Brass 20/15 Long/Short Arm
HANSEN SUPERFLO VALVE BROCHURE AND CHEAT SHEETS
- For HANSEN Superflo Valve Brochure and Cheat Sheets, refer to Hansen Australia Website.
HANSEN SUPERFLO AND HIFLO HANDY TIPS AND COMMERCIAL VIDEOS
- For HANSEN Superflo and Hiflo Handy Tips and Commercial Videos, refer to Hansen Australia Website.
FREQUENTLY ASKED QUESTIONS
- QUESTION: At certain times of the year I need to run portable troughs in my paddocks, is it possible to run these off my existing Super-Flo valve?
- ANSWER: Yes, the Super-Flo Trough Valve incorporates a 25mm (1”) thread on the valve outlet that can utilised the spare adaptors that come with the valve to enable to attach any number of poly pipe fittings to the Super-Flo trough Valve. This off take can be used for any number of farm applications.
- QUESTION: At present, I get valve bounce in my troughs, will the Super-Flo valve stop this?
- ANSWER: Yes, valve bounce is created from high flows at high pressures, because the Hansen Super-Flo valve delivers higher flows than other valves; it will effectively reduce line pressure which in return will reduce the incidences of this problem by also reducing water hammer.
- QUESTION: I have problems with having to forever clean my valves as my water supply can get dirty at times, how will the Hansen Super-Flo valve handle these conditions?
- ANSWER: We have designed the Hansen Super-Flo valve to work in either clean or dirty water situations.
- QUESTION: My troughs have both 20mm & 25mm threaded inlets, does your Hansen Super-Flo Valve come in both sizes?
- ANSWER: Yes, the Hansen Super-Flo Valve comes with the required components to install in 20mm or 25mm threaded inlets. This of course means you only need to buy one valve for all sized inlets.
- QUESTION: The valves I have a present have a tendency to jam open or closed costing me time and either a bog around my trough or no available water for my stock, will your valves stop this problem?
- ANSWER: Yes, the Hansen Super-Flo valve has a new patent pending “Slipper Fit Piston” design seal assembly to minimise this problem.
- QUESTION: What pressure can I run my Hansen Super-Flo Valve at?
- ANSWER: The Hansen Sueper-Flo Valve will operate from 0.2 bar to 12 bar.
- QUESTION: Will the higher flow cost me more to run my pump?
- ANSWER: No, because the Hansen Super-Flo valve is more efficient than what you are used to. The reduced operating pressure required will equate to higher flows at lower pressures at your pump which in turn will reduce pumping time and cost.
