Description
Hansen 20mm x 10mm (3/4″ x 3/8”) Reducing Bush, BSPT x BSPT / HRB2010
This is used to reduce the size of Female Threads.
FEATURES AND BENEFITS
- Largest range of durable, high strength, commercial quality threaded pipe fittings in the Southern Hemisphere.
- Precision, heavy duty, tapered threads give a strong reliable seal.
- Manufactured from a raw material approved for use with potable (drinkable) water.
- Manufactured from high quality glass fibre, reinforced nylon, giving a weather, termite, fungi and bacteria resistant.
- Common applications include horticultural, agricultural, irrigation, marine & plumbing.
- Material strong enough to minimise potential cross threading.
- Suitable for use above or below ground in varying operating pressures and temperatures.
- Strong, lightweight and compact.
- Available in a variety of thread combinations and connections.
- Made in New Zealand.
SPECIFICATIONS
- PRODUCT CODE: HRB2010
- CODE MEANING: HANSEN REDUCING BUSH
- SIZE: 20mm x 10mm (3/4″ x 3/8”)
- TYPE: BSPT x BSPT
- PRESSURE AND FLOW RATES (Refer to “True Fit Pipe Fittings Maximum Working Pressures” in image gallery for graph and details)
FITTING SIZE MAX PRESSURE @ 20 DEGREE CELSIUS 6mm-50mm 16 Bar (1600 kPa, 235 psi) 65mm 12 Bar (1200 kPa, 175 psi) 80mm-100mm 10 Bar (1000 kPa, 145 psi)
Hansen have tested all its products for use with cold water up to a maximum temperature of 60°C (140°F). We do not recommend the use of these products with temperatures higher than 60°C (140°F) as plastic expands due to temperature increases. Hansen cannot guarantee the products will perform when used with temperatures over 60°C (140°F). Hansen products that have failed in temperatures higher than 60°C (140°F) will not be covered by our Hansen Warranty.
- CHEMICAL RESISTANCE OF TRUE FIT THREADED FITTINGS
- Please refer to “True Fit Threaded Fittings Chemical Resistance Chart” in image gallery for specifications and chemical resistance details.
- True Fit Threaded Fittings are AWQC AS/NZS 4020:2018 and WRAS Approved Product, refer to Hansen Australia Website.
- DIMENSIONS (See image gallery or below chart for visual sizing guide)
- T1 BSPT: 3/4″ (20mm)
- T2 BSPT: 3/8″ (10mm)
- SIZE a: 29mm
- SIZE b: 25mm
- TRUE FIT THREADED FITTINGS MATERIALS
- BODY AND NUTS MATERIAL: High Quality Glass Fibre Reinforced Nylon
ALSO AVAILABLE REDUCING BUSH IN DIFFERENT SIZES: (Available as seperate purchase)
- HRB1506 15mm x 6mm (1/2” x 1/8”)
- HRB1508 15mm x 8mm (1/2” x 1/4”)
- HRB1510 15mm x 10mm (1/2” x 3/8”)
- HRB2008 20mm x 8mm (3/4” x 1/4”)
- HRB2015 20mm x 15mm (3/4” x 1/2”)
- HRB2508 25mm x 8mm (1” x 1/4”)
- HRB2510 25mm x 10mm (1” x 3/8”)
- HRB2515 25mm x 15mm (1” x 1/2”)
- HRB2520 25mm x 20mm (1” x 3/4”)
- HRB3215 32mm x 15mm (1 1/4” x 1/2”)
- HRB3220 32mm x 20mm (1 1/4” x 3/4”)
- HRB3225 32mm x 25mm (1 1/4” x 1”)
- HRB4015 40mm x 15mm (1 1/2” x 1/2”)
- HRB4020 40mm x 20mm (1 1/2” x 3/4”)
- HRB4025 40mm x 25mm (1 1/2” x 1”)
- HRB4032 40mm x 32mm (1 1/2” x 1 1/4”)
- HRB5015 50mm x 15mm (2” x 1/2”)
- HRB5020 50mm x 20mm (2” x 3/4”)
- HRB5025 50mm x 25mm (2” x 1”)
- HRB5032 50mm x 32mm (2” x 1 1/4”)
- HRB5040 50mm x 40mm (2” x 1 1/2”)
- HRB6532 65mm x 32mm (2 1/2” x 1 1/4”)
- HRB6540 65mm x 40mm (2 1/2” x 1 1/2”)
- HRB6550 65mm x 50mm (2 1/2” x 2”)
- HRB8040 80mm x 40mm (3” x 1 1/2”)
- HRB8050 80mm x 50mm (3” x 2”)
- HRB8065 80mm x 65mm (3” x 2 1/2”)
- HRB10050 100mm x 50mm (4” x 2”)
- HRB10065 100mm x 65mm (4” x 2 1/2”)
- HRB10080 100mm x 80mm (4” x 3”)
TRUE FIT THREADED FITTINGS QUICK AND EASY INSTALLATION STEPS (See full installation in image gallery or attached image)
- 1.) (a) Use a thread paste sealant or (b) a teflon tape sealant. The right sealant for threaded joints is non-hardening, compatible with plastic and doesn’t add slipperiness to encourage over-torquing.
2.) Screw pipe into fitting. Do not over tighten. The recommended way to assemble a Threaded Pipe Fitting is hand tight. Tighten until firm with spanner or pipe grip. One to two turns should be all that is required.
- All pipe work must be adequately supported.
- Use a thread sealant on all threaded connections. It is recommended to use Loctite 5331.
- If you are using chemicals or have any special requirements that you wish to use your Threaded Pipe Fitting in, see the Threaded Chemical Resistance chart in the image gallery.
- Please see below for Minimum Recommended Hole Sizes chart.
- Fittings should be installed as per applicable standards and approvals for pipe and fittings. Failure to complete installation in accordance with applicable standards and approvals may void warranties given by Hansen Products (NZ) Limited in respect to the fitting. It is recommended to follow pipe manufacturers guidelines.
TRUE FIT THREADED FITTINGS BROCHURE AND CHEAT SHEETS
- For HANSEN True Fit Threaded Fittings Brochure and Cheat Sheets, refer to Hansen Australia Website.
TRUE FIT THREADED FITTINGS HANDY TIPS AND COMMERCIAL VIDEOS
- For HANSEN True Fit Threaded Fittings Handy Tips and TV Commercial videos, refer to Hansen Australia Website.
FREQUENTLY ASKED QUESTIONS
- QUESTION: Can I use Hansen True Fit Fittings under driveways, paths and foundations?
- ANSWER: Hansen does not recommend the use of any Hansen True Fit Fittings under any driveways, paths or foundations.
- QUESTION: Can I use my Hansen fittings with my swimming pool/spa pool set up?
- ANSWER: No, as the high concentration of chlorine used in the water for pools will attack the material. The fitting material is only suitable for use with domestic water. Hansen products that are used in this application will not be covered by our Hansen Warranty..
- QUESTION: Can I use these fittings with metal fittings?
- ANSWER: Yes. For more information on installation tips refer to installation instructions.
- QUESTION: Do I need to support my fittings?
- ANSWER: Yes. All pipe work must be adequately supported.
- QUESTION: Does this fitting carry the Hansen Warranty?
- ANSWER: Yes, all Hansen manufactured products carries a Hansen Warranty.
- QUESTION: How tight should I tighten my Hansen threaded fittings?
- ANSWER: Do not over tighten. The right way to assemble a threaded fitting is hand tight plus one to two turns – no more! For more information on installation tips refer to installation instructions.
- QUESTION: What temperature can I use Hansen fittings at?
- ANSWER: Hansen have tested all its products for use with cold water up to a maximum temperature of 60°C (140°F). It is not recommended to use of these products with temperatures higher than 60°C (140°F) as plastic expands due to temperature increases. Hansen cannot guarantee the products will perform when used with temperatures over 60°C (140°F). Hansen products that have failed in temperatures higher than 60°C (140°F) will not be covered by the Hansen Warranty.
- QUESTION: What type of thread sealant should I use?
- ANSWER: Use a thread sealant on all threaded connections. It is recommended to use Loctite 5331.
